DIY: 2011 ~ 2017 LEAF Horn Upgrade


I don’t know what it is with the horns on Hybrids and other Eco cars. They all seem to have horns that were designed by Droopy Dawg. For me that just does not work, I want a horn that shouts respect when I am in the Slow lane and someone tries to mix it up with me!

In the past my weapon of choice has been the 118db Hella SuperTone Twin Horn Kit. These bad boys will make a dead person jump!

But at the recommendation of several of my Leaf owner friends, I decided to try the FIAMM 74100 El Grande – Twin Horns. At under $20, they are a real value, they sound like my old 68 Buick, blast at 110db, and have a real tone of refinement. These horns are PnP, and don’t need a relay to operate.

Replacing the stock horn is rated moderately difficult, and takes less than an hour. Installation can be done from the top of the car or from the bottom, The easiest is to go in from the top of the motor compartment.

Recommended tools and supplies:

  • Wire stripper for 18 gauge wire (or a sharp knife)
  • Flat bladed screwdriver or tack puller for removing the plastic fasteners
  • 10mm socket with long extension bar (for removing the coolant reservoir)
  • 12mm socket with short extension bar (for the horn)
  • Magnetic “reaching stick” to retrieve any dropped hardware that gets stuck in the belly pan
  • crimper (often included with the wire stripper)
  • 18 gauge stranded wire (about 2 feet of wire)
  • 1 Male 14-16 gauge “disconnect” connector
  • 2 Female 22-18 (or 14-16) “disconnect” connectors

To Start, make sure the car is off, and in a comfortable place to work.

Accessing the Horn from the top of the car

Next open the hood and remove the front bezel that covers the radiators. It is held in with way too many pop fasteners, but they are easily removable with a small screwdriver to pry them up.

You are going to be working in the area in the front where the windshield washer fluid container neck and the coolant overflow tank is.

If you look down into the car where the coolant overflow tank is you can see the stock horn.

To easily get at the horn, you need to get the coolant overflow tank out of the way.

It is held in with 2 10mm bolts, and has 2 small hoses at the bottom of the tank that go to the 2 coolant systems in the car. Make sure that the cap is on the  tank tightly, and simply remove the two bolts and lift the tank up and rest in on the cross-member bar as shown.

Now you have plenty of room to get at the old horn and to install the new ones.

Accessing the horn from under the car – Thanks to Tony Williams for use of his underside photos
Another method of accessing the horns is from under the car.  This method is used primarily for 2013 through 2017 models. This requires you to crawl under the car to remove the front underbody panel. This is probably best done by driving the car up on ramps, putting the car on jack stands, or on a lift. Use extreme car when working under the car, make sure that the parking brake is set, and that your lifting method is secure. Proceed at your own risk.

The underbody panel is made of some sort of soft lightweight material and is there primarily for aerodynamic reasons. It is fastened to the body with 6 10mm bolts and 6 pop fasteners. Note the 2 front outside bolts are longer than the rest and do not have philips screw heads.

After you get the cover removed, the horn is accessible. Note from this view you can see the bottom of the coolant overflow tank.

Please note that on newer 2012 models and some older cars in colder climates, Nissan added a crush panel between the front bumper ram and the lower crossmember.  Unfortunately, removing this panel requires removal of the front bumper cover and bumper ram, so upgrading your horn from the top is your best bet.

Once you have access to the old stock horn, then it is time to remove and replace it.  The stock horn is held on a short bracket that is bolted to the center brace with a 12mm bolt. Take out the horn and bracket, and disconnect the power and ground leads. Note that the power and ground cables are different lengths.  The short one is the power cable and the long one is the ground.  It is important to remember this when the new horns are connected.

The new horn assembly has two brackets to hold them apart. Bolt the brackets and a ground lug to the horns securely. A good idea is to add a drop of Loctite to the horn bolts. Make sure that when you install your horns, that they are pointing DOWN, so they don’t collect water.

TIP: Stick a piece of masking tape in the 12mm socket that you are using to tighten down the horn bracket bolt. This will help prevent you dropping the bolt and it getting stuck under the radiator crossmember and the belly pan. If you do drop the bolt you can use a magnetic reaching stick to fish it out, or pop a few of the belly pan fasteners along the corner of the pan and reach in and retrieve the bolt. Either way is a pain, so be careful!

IMPORTANT: Make sure you do not have the horn wiring crimped under the horn bracket before you tighten down the bracket. If you crimp the wiring you may short out the horn circuit and blow the horn fuse.

To wire up the new horns to the existing wiring requires making a short pigtail for the power lead. The existing stock ground line (the long wire) connects directly to the ground lug that is bolted to the horn bracket.

Make sure that that the single power lug (which plugs into the existing horn power connector) is a male blade.

Now you are ready to install the new horn assembly. The two horns and their brackets get bolted to the original horn bracket, and that in-turn gets bolted to the car’s center brace. Connect your power and ground wires to the power pigtail and to the ground lug respectively.

IMPORTANT: The power lead (the one that you connect the pigtail to) is the SHORTER cable. The ground wire is the LONGER cable. Don’t mix them up or you will blow the horn fuse!

Some installers stick a piece of shrink tubing over the power connector to pigtail connection, just to make sure there was no chance of shorting. This is highly recommended.

Give your new horns a try, and if they work, then reinstall the coolant overflow tank, and the top cover, and you are done!

Enjoy! For me this was the best $20 and hour of my time that I have spent all week!

They sound great. Get a pair and see for yourself!

Here is a short video of before and after, Credit: mwalsh: